Merry Christmas to All

Christmas Craft Projects - Santa

Folk art fun! This adorable free scroll saw pattern is a must for any santa collector! Easy to make!

Free santa scroll saw patterns - Merry Christmas to All


Designed by:

Pine Country Decor
by Lily Hadrava





























    Pattern:



    #00 liner brush
    #3 round brush
    Three 1" sponge brushes
    And old scruffy/stippler brush
    #10 floater/flat brush
    #6 floater/flat brush
    1/2" pine board & 3/4" pine board (or precut wood kit)
    Oil base stain
    The cuff of an old red or green sock
    3 buttons
    Fine sanding disc
    Tack cloth
    An old medium bristled toothbrush
    20 gauge wire & wire cutters
    tracing and transfer paper
    stylus
    1" x 5" scrap of fabric
    drill & 5/64" drill bit
    tacky or wood glue
    scissor
    clear acrylic matte spray



Copyright 2004 Lily Hadrava & www.pinecountrydecor.com

    Paints needed: Ceramcoat by Delta
    Ivory
    Black Cherry
    Candy Bar Brown
    Black
    Medium Flesh
    Sonoma Wine

    Antiquing Medium: Folkart by Plaid
    Down Home Brown





1. Drill holes in arms and shoulders as indicated on the pattern.
2. Stain all pieces of wood with your favorite oil based stain. Let dry for at least one hour.
3. Using the sponge brushes, basecoat the pieces. Basecoat Santa's body and legs in Black Cherry. Basecoat the arms and cuffs in Black Cherry. Basecoat the face in Medium Flesh. Basecoat the boots and mittens in Black. (Remember to paint the sides as well as the front.)
4. When dry, sand all pieces with a sanding disc and wipe with a tack cloth.
5. Trace the pattern onto the wood using the tracing and transfer paper and the stylus.
6. Using a stippler or scruffy brush, stipple Ivory on the fur trim of the coat and cuffs. Let dry.
7. Using a #10 floater/flat brush, basecoat the beard in Ivory.
8. Dry brush in Ivory with a #00 liner brush on the boots and mittens. (Indicated on the pattern as ------.)
9. Stipple the cheeks with Sonoma Wine. Dot the nose with the end of your paint brush in Black Cherry. Dot the eyes in Black.
10. Using the #6 floater/flat brush, float Candy Bar Brown around the beard, the fur trim and above the cuffs. Also, make a float to divide the legs. (Indicated on the pattern as ////////.)
11. Stipple a second coat of Ivory onto the fur trim and the cuffs.
12. Using a #3 round brush, pull teardrops (or comma strokes) of Ivory downward from the cheeks to make the beard.
13. Using the #3 round brush again, pull the mustache from the center outward.
14. Using the stylus, place a small dot of Ivory on the top of each cheek.
15. When the ?fur? has dried, us the liner brush to put small Black lines on the fur trim and cuffs to look like soot.
16. Using the #00 liner brush, make two small teardrops in Ivory for the eyebrows.
17. When the beard is completely dry, put on a second coat of Ivory teardrops. Let the beard dry and put on a second coat of teardrops on the mustache.
18. Using the #00 liner brush, put a small Ivory dot in each eye.
19. Using an old toothbrush, splatter all pieces in Black and with a clean toothbrush, splatter all pieces in Ivory.
20. When all pieces are completely dry, antique them.
21. Wire on the arms.
22. Glue on the boots and place a few drops of glue behind each arm to hold them in place.
23. Glue on the buttons. Glue on the cuff of an old sock for a hat. Tie a 1" x 5" fabric scrap at the end of the hat. If you like, snip the end of the sock hat to look like a tassel.
24. Spray with a matte spray after the glue has dried.
25. Sign, date and show off!


Copyright 2011 Lily Hadrava. Design may be used for fun or profit. This design may not be mass produced for the wholesale market without written permission. All rights reserved.